Aluminum (Al) - based powders have attracted attention as key materials for 3D printing because of their excellent specific mechanical strength, formability, and durability. Although many studies on the fabrication of 3Dprinted Al-based alloys have been reported, the influence of the size of raw powder materials on the bulk samples processed by selective laser melting (SLM) has not been fully investigated. In this study, AlSi10Mg powders of 65 μm in average particle size, prepared by a gas atomizing process, are additively manufactured by using an SLM process. AlSi10Mg powders of 45 μm average size are also fabricated into bulk samples in order to compare their properties. The processing parameters of laser power and scan speed are optimized to achieve densified AlSi10Mg alloys. The Vickers hardness value of the bulk sample prepared from 45 μm-sized powders is somewhat higher than that of the 65 μm-sized powder. Such differences in hardness are analyzed because the reduction in melt pool size stems from the rapid melting and solidification of small powders, compared to those of coarse powders, during the SLM process. These results show that the size of the powder should be considered in order to achieve optimization of the SLM process.

Citations

Citations to this article as recorded by  

• Laser Soldering Process Optimization of MEMS Probe of Probe Card for Semiconductor Wafer Test
  Myeongin Kim, Won Sik Hong, Mi-Song Kim
  Journal of Welding and Joining.2022; 40(3): 271.     CrossRef
• Investigation on Interfacial Microstructures of Stainless Steel/Inconel Bonded by Directed Energy Deposition of alloy Powders
  Yeong Seong Eom, Kyung Tae Kim, Soo-Ho Jung, Jihun Yu, Dong Yeol Yang, Jungho Choe, Chul Yong Sim, Seung Jun An
  Journal of Korean Powder Metallurgy Institute.2020; 27(3): 219.     CrossRef

In this study, the electroless nickel plating method has been investigated for the coating of Ni nanoparticles onto fine Al powder as promising energetic materials. The adsorption of nickel nanoparticles onto the surface of Al powders has been studied by varying various process parameters, namely, the amounts of reducing agent, complexing agent, and pH-controller. The size of nickel nanoparticles synthesized in the process has been optimized to approximately 200 nm and they have been adsorbed on the Al powder. TGA results clearly show that the temperature at which oxidation of Al mainly occurs is lowered as the amount of Ni nanoparticles on the Al surface increases. Furthermore, the Ni-plated Al powders prepared for all conditions show improved exothermic reaction due to the selfpropagating high-temperature synthesis (SHS) between Ni and Al. Therefore, Al powders fully coated by Ni nanoparticles show the highest exothermic reactivity: this demonstrates the efficiency of Ni coating in improving the energetic properties of Al powders.

Citations

Citations to this article as recorded by  

• Study on the Combustion Characteristics of Ethanol Nanofuel
  Kwanyoung Noh, Hyemin Kim, Siwook Nam, Soonho Song
  Aerospace.2023; 10(10): 878.     CrossRef
• The Self-Reduction during the Thermal Decomposition of an Ammonium Molybdate
  Kyoungkeun Yoo, Won Beom Koo, Hanggoo Kim, Sang-hun Lee
  Minerals.2023; 13(2): 133.     CrossRef
• Increased exothermic reactivity of polytetrafluoroethylene-coated aluminum powders: Impact of powder size reduction
  Soo-ho Jung, Kyung Tae Kim, Jinhee Bae, Yoon Jeong Choi, Jae Min Kim, Jeong-Yun Sun
  Materials Letters.2023; 351: 135009.     CrossRef
• High energy Al@Ni preparation of core-shell particles by adjusting nickel layer thickness
  Yongpeng Chen, Jianguo Zhang, Jiawei Zhu, Ning Xiang, Huichao Zhang, Zunning Zhou
  Vacuum.2022; 205: 111344.     CrossRef
• Electroless deposition of Ni nanoparticles on micron-sized boron carbide particles: Physicochemical and oxidation properties
  Prashant Ravasaheb Deshmukh, Hyung Soo Hyun, Youngku Sohn, Weon Gyu Shin
  Korean Journal of Chemical Engineering.2020; 37(3): 546.     CrossRef
• Synthesis and exothermic reactions of ultra-fine snowman-shaped particles with directly bonded Ni/Al interfaces
  Gu Hyun Kwon, Kyung Tae Kim, Dong Won Kim, Jungho Choe, Jung Yeul Yun, Jong-Man Kim
  Applied Surface Science.2019; 476: 481.     CrossRef

Graphene oxide (GO) powder processed by Hummer's method is mixed with p-type Bi₂Te₃ based thermoelectric materials by a high-energy ball milling process. The synthesized GO-dispersed p-type Bi₂Te₃ composite powder has a composition of Bi_0.5Sb_1.5Te₃ (BSbT), and the powder is consolidated into composites with different contents of GO powder by using the spark plasma sintering (SPS) process. It is found that the addition of GO powder significantly decreases the thermal conductivity of the pure BSbT material through active phonon scattering at the newly formed interfaces. In addition, the electrical properties of the GO/BSbT composites are degraded by the addition of GO powder except in the case of the 0.1 wt% GO/BSbT composite. It is found that defects on the surface of GO powder hinder the electrical transport properties. As a result, the maximum thermoelectric performance (ZT value of 0.91) is achieved from the 0.1% GO/BSbT composite at 398 K. These results indicate that introducing GO powder into thermoelectric materials is a promising method to achieve enhanced thermoelectric performance due to the reduction in thermal conductivity.

Citations

Citations to this article as recorded by  

• Exploring Thermoelectric Transport Properties and Band Parameters of n-Type Bi2-xSbxTe3 Compounds Using the Single Parabolic Band Model
  Linh Ba Vu, Soo-ho Jung, Jinhee Bae, Jong Min Park, Kyung Tae Kim, Injoon Son, Seungki Jo
  journal of Korean Powder Metallurgy Institute.2024; 31(2): 119.     CrossRef
• Enhancing Electrical Properties of N-type Bismuth Telluride Alloys through Graphene Oxide Incorporation in Extrusion 3D Printing
  Jinhee Bae, Seungki Jo, Kyung Tae Kim
  journal of Korean Powder Metallurgy Institute.2023; 30(4): 318.     CrossRef
• Advancement of thermoelectric performances through the dispersion of expanded graphene on p-type BiSbTe alloys
  Eun-Ha Go, Rathinam Vasudevan, Babu Madavali, Peyala Dharmaiah, Min-Woo Shin, Sung Ho Song, Soon-Jik Hong
  Powder Metallurgy.2023; 66(5): 722.     CrossRef
• The role of edge-oxidized graphene to improve the thermopower of p-type bismuth telluride-based thick films
  Young Min Cho, Kyung Tae Kim, Gi Seung Lee, Soo Hyung Kim
  Applied Surface Science.2019; 476: 533.     CrossRef
• The Preparation and Growth Mechanism of the Recovered Bi2Te3 Particles with Respect to Surfactants
  Hyeongsub So, Eunpil Song, Yong-Ho Choa, Kun-Jae Lee
  Journal of Korean Powder Metallurgy Institute.2017; 24(2): 141.     CrossRef